Ableton Live - Mixer Controls

This default Ableton Live - Workspace 6 presents an alternative Session View workflow with actions and functions as well as editing tools, but with less focus on clips than Clip Launch Mode.

트랙/재생 다이얼 선택
Upon entering this workspace, you will see a dial on top right that is used to select a track, but it also has a Play/Stop action as its press function.

PROTIP! Mouse is a nice companion to Live. For example, when mixing a large multitrack project and adjusting track levels, it’s a very efficient workflow to use one hand to mouse-click on a desired track – or use this dial to select a track – and then use the other hand to adjust track levels with the top-left track level dial.


트랙 볼륨 및 패닝

Choose a track, and then you can use Track Volume and Track Panning to set the level and pan position of the desired track. Note that with these controls, too, pressing down on a dial returns the parameter to its default value (level returns to zero, and panning returns to center). These can be used for audio and MIDI tracks as well as return tracks.

 

마스터 볼륨
On bottom left, Master Volume dial control can be found.

 

Cue level
There is a dial for cue level. Unlike in Ableton Live, setting Cue level while auditioning samples from the browser does not the playback of the sound that is being previewed.

음소거 및 솔로 트랙
Muting and soloing a track is as easy as selecting a track and tapping Mute and Solo pads.

TIP! If you do a lot of soloing and muting, you could even assign mute and solo to the track select dial, so you could use the same dial to select a track and then mute or solo it by pressing down on the dial!


컨트롤 전송
Send controls (for sending signal to Return tracks) are on the second dial page. The default profile has controls for six sends (A–E). You can have more than that: Loupedeck app will allow you to add 12 sends to your profile (they can be found for dials under Adjustments→Track folder in the Setup software).

팁 ! 모든 믹서 컨트롤은 드럼랙 내에서도 작동합니다. 트랙 선택 다이얼을 사용할 수 있습니다. 드럼 랙 내부로 스크롤하고 믹서 컨트롤을 조작합니다. 라이브는 마우스의 좋은 동반자이며, 마우스로 원하는 트랙을 선택한 다음 라이브를 사용하여 원하는 작업(예: 솔로)을 수행하는 것도 매우 편리합니다. 드럼 랙 내부에 체인을 직접 만든 경우에도 드럼 랙 내부에 작업을 전송합니다.
Get dubbing!


라우팅 및 모니터링

In addition to offering a monitoring function, the second touch page on this workspace offers functions for routing and monitoring. You can adjust the following things:


• Input Routing Type. On audio tracks, this toggles  between sources that are available for the Audio From field. Here you can choose from an external input source (if it has
been set in Audio settings in preferences), resampling the audio engine, and all available audio tracks as well as Return tracks.


입력 라우팅 채널. 외부 입력에서 녹음하는 경우 외부 입력 트랙(예: 오디오 인터페이스가 제공해야 하는 입력 트랙)에서 선택합니다. Live의 트랙에서 녹화하는 경우 이 선택기는 Pre FX, Post FX 및 Post Mixer에서 선택합니다.


출력 라우팅 유형: 트랙의 출력 대상(마스터, 프로젝트의 오디오 트랙, 송신만, 외부 출력)을 설정하려면 이 옵션을 사용합니다.


출력 라우팅 채널: 오디오 인터페이스에 여러 출력이 있는 경우(기본 설정의 오디오 설정에서 활성화됨) 사용 가능한 모든 출력을 전환합니다.