Ableton Live - Clip Parameter Mode

Clip Mode allows for editing of clip parameters. This mode works for both Arrangement and Session View clips. What is seen on Loupedeck device in this mode varies depending on whether an audio clip or a MIDI clip is currently selected.

Due to the way this dedicated dynamic workspace has been built, it is not customizable. Some of the actions are executed differently, depending on whether you are using  Loupedeck CT or Live.

First, click on a clip to reveal actions for pads and dials. Use either the second wheel or the Skip ←→ dial of this workspace to change clip selection on Arrangement when clip view is open (if you use the Skip ←→ dial, make sure to not highlight the top bar of a clip, or else the dial will move the clip).


Moving the playhead this way selects the clip whose parameters you are able to tweak, and you will always see the parameters of the currently selected clip in the bottom bar in Live (note that with this workflow you don’t necessarily have to click on a clip as long as you have clicked of Arrangement once).


예를 들어 (위 사진), 두 번째 휠 회전 또는 Skip ←→ 다이얼을 사용하여 6개의 오디오 클립 사이에서 플레이헤드를 이동하면 사용자가 클립에 대한 다른 게인을 빠르게 설정하고 값을 바꿀 수 있습니다. 표시되는 동영상은 플레이헤드가 현재 어떤 클립 영역에 있는지 기준으로 합니다.


In Loupedeck CT; If you want to zoom in on a clip, first click on the clip view and then use the first wheel. If you click on Arrangement, the first wheel zooms Arrangement.


AUDIO CLIP - dials

색상

Can be used to scroll through the color selection to assign a new color to the clip.

Start/end marker

When looping is enabled, these controls can be used to set the clip’s start and end points.

Clip/loop start

When looping is enabled, this controls the starting point of the loop brace.When looping is not enabled, this controls the starting point of the clip.

Clip/loop end

When looping is enabled, this controls the end point of the loop brace. When looping is not enabled, this controls the end point of the clip

Clip/loop position
This sets the loop position.

Gain
For setting the gain of the clip in 0.1 dB increments.
Pushing down on the clip gain resets it to zero.

Semitone
For adjusting the sample pitch transposition in semitones.

Detune
For adjusting the sample pitch transposition in cents.

AUDIO CLIP – touch pads

루프 켜기/끄기
Enables and disables the clip’s looping. Set its length and position with dials.

Warping on/off
Enables and disables the clip’s warping.

Warp 모드
For changing the clip’s current warping mode. Only works when warping is active.

RAM에 로드
Loads the audio of the clip into your computer’s memory instead of reading it in real-time.
This may lessen the hard disk load. Useful if you are getting lots of hard disk overloads (indicated by the “D” symbol on top right of Live).


MIDI CLIP-다이얼

색상
Can be used to scroll through the color selection to assign a new color to the clip.

Start/end marker
When looping is enabled, these controls can be used to set the clip’s start and end points.

Clip/loop start
When looping is enabled, this controls the starting point of the loop brace.
When looping is not enabled, this controls the starting point of the clip.

Clip/loop end
When looping is enabled, this controls the end point of the loop brace.
When looping is not enabled, this controls the end point of the clip.

Clip/loop position
This sets the loop position.


MIDI CLIP – touch pads

루프 켜기/끄기
Enables and disables the clip’s looping. Set its length and position with dials.

Crop
Crop function deletes material that is not inside the current clip loop region.

Duplicate loop
This action duplicates the loop and doubles its duration.